Choosing an A Series Pool Cleaner for Your Market — A013, A012 and Four Newer Models

When a buyer asks us which A Series model to stock, we start with the pools in their market, not with the spec sheet. A floor cleaner that matches those pools is judged on what it does well. One that doesn't match creates support work for everyone in the chain.
This is how we work through the choice for A013, our lead floor-cleaning model, for A012, which shares its performance, and for the four newer models we now list.
Start with the pools, not the robot
A013 and A012 are specified for pools of 100 m² in the standard configuration, with a listed water depth of 2 m and pool water temperatures of 5–35 °C. Treat the 100 m² figure as a starting point. Pool shape and floor conditions still need checking.
The floor usually decides more than the size. Steps are unsuitable, slopes over 23° are unsuitable, and individual slopes at or below 23° still need assessment. Pits and narrow recesses can trap the cleaner. That makes both models a fit for small to medium residential pools with a regular floor, where the daily job is leaves, sand, small stones and other everyday debris.
A013 or A012 — same performance, different body
The two models share the same standard performance. Each runs on a 5200 mAh, 11.1 V battery (3.7 V cells in a 3S2P arrangement) with a 36 W motor, and gives 120–180 minutes of runtime from a full charge. Both use a 180 µm filter, a 2.5 L debris basket, two bottom brushes, 3.5 m³/h filtration and a travel speed of 12–14.4 m/min, and both are rated IPX8.
What differs is the body and the box:
- A013 comes in dark blue or royal blue and measures 365×310×170 mm. It weighs 3.8 kg net and 5 kg gross, in a 440×340×195 mm package.
- A012 is white and measures 380×335×175 mm. It weighs 3.5 kg net and 4.6 kg gross, in a 430×340×190 mm package.
A013 is our current lead model, so it is the natural starting point for a new range. A012 makes sense when a white body suits your brand or channel better. Whichever you choose, check the certification requirements for that specific model, because coverage depends on the model, configuration and target market, and we confirm it with you before the order.
What runtime and basket size mean in daily use
The 120–180 minute range moves with pool shape and load. Magnetic speed sensing adjusts propulsion as the cleaner travels, using less thrust in normal travel and more when turning or meeting a slope. Suction is handled separately through the fluid design.
A run does not always end with an empty battery. When a loaded filter slows the cleaner down, or battery power falls below 10%, it parks by the wall so it is easier to lift out. In pools with heavy leaf fall, the 2.5 L basket can set the limit before the battery does. Recharging takes 2.5–3 hours, and the battery is rated for 800 cycles, each a full charge in normal pool water.
In markets with a long off-season, storage matters as much as runtime. If a cleaner will be unused for more than 3 months, it should be charged to above 70% every 3 months and stored at -5 to 35 °C with no more than 75% relative humidity. Put that in the manual rather than leaving it to after-sales.
Floor-only by design
A013 and A012 clean the pool floor only. They do not climb walls, clean steps, avoid obstacles actively or map a path; they travel across the floor and reverse when they meet the wall. If buyers in your market expect wall cleaning, choose a different model rather than stretching the description of these two.
Where the newer models fit
We also list four newer A Series models. Their published specifications are shorter, so ask us for the full sheet before you plan a range around one of them:
- A019 is a cordless floor cleaner in grey. It runs 120–180 minutes depending on the cleaning mode, climbs slopes of up to 23° and collects debris in a 2.5 L basket. When cleaning is finished, the filter is full or the battery is low, it docks at the wall and beeps.
- A021 uses track drive and dual brushless motors for 30 m³/h of suction. Smart path planning covers the floor in a zigzag pattern that adapts to the pool shape, and it can be steered with a LiFi underwater remote control or a mobile app. It parks at the pool edge after cleaning.
- A022 cleans the floor and walls on dual tracks. Its 7800 mAh battery gives about 180 minutes after a 4-hour charge, and it combines sonar detection with smart path planning and 300 µm filtration.
- A023 is a track-drive floor and wall cleaner with an all-surface climbing brush, a 180 W suction motor and 30 m³/h of suction. A 7800 mAh battery gives 2–3 hours of cleaning, and it is rated IP68 with one-touch start.
Stock, OEM and lead times
Our own available stock ships from 1 unit in its existing configuration, and A Series stock orders within 20 units are supplied from available stock. Small batches built from stocked raw materials take about 15 days, full-container orders about 30 days and peak-season production 45 days. Logo and color OEM orders start at 100 units per model.
Tell us your target market, the pool sizes you sell into and the quantity you have in mind, and we will suggest the A Series model that fits.







